Kaizer Power Electronics

[...] Today I put the last parts together on small project with a large impact. A 4000 joule capacitor bank able of delivering destructive short circuit currents in the thousands. The first test was [...]

[...] Today I put the last parts together on small project with a large impact. A 4000 joule capacitor bank able of delivering destructive short circuit currents in the thousands. The first test was [...]

This afternoon I had my current monitor and oscilloscope hooked up to the capacitor bank to do current measurements of the short circuit energy. The r [...]

This afternoon I had my current monitor and oscilloscope hooked up to the capacitor bank to do current measurements of the short circuit energy. The r [...]

[...] Here is an update with work that have been done last week on the large DRSSTC. This update will show you half of the mmc, the enclosure, the platform, new primary supports [...]

[...] Here is a small update with some of the work that have been done on the large DRSSTC. This is my first project where I will post information and pictures about the progress as the [...]

[...] Due to a busy work year and not many days at home the progress with the large DRSSTC have been very limited. I have however updated the article with the testing progress and fault [...]

[...] voltages apparatuses. None the less there is still progress and here is some of it for the large DRSSTC currently under way. All the pictures can be seen at the bottom of the page: http:// [...]

[...] ! I hope you enjoy this video This video is located at the bottom of the article for the Kaizer DRSSTC II: http://kaizerpowerelectronics.dk/tesla-coils/kaizer-drsstc-ii/ [...]

After driving the small TO-247 IGBTs so hard that they eventually failed, I have now upgraded the half bridge with a couple of IXGN60N60C2D1 isotop IG [...]

I made a small DRSSTC which only lasted a couple of runs before the TO-247 IBGTs have to give up. It gave a good 24 cm sparks will get upgraded in th [...]

After driving the small TO-247 IGBTs so hard that they eventually failed, I have now upgraded the half bridge with a couple of IXGN60N60C2D1 isotop IG [...]

[...] This is the first test run of a royer induction heater running at 650 Watt, there is heavy voltage sag on the DC supply. The heated bolt is a [...]

[...] This is the first test run of a royer induction heater running at 650 Watt, there is heavy voltage sag on the DC supply. The heated bolt is a [...]

Being the lucky person to suffer from having a work, there is little time to maintain building on all the high voltages apparatuses. None the less the [...]

Due to a busy work year and not many days at home the progress with the large DRSSTC have been very limited. I have however updated the article with t [...]

Being the lucky person to suffer from having a work, there is little time to maintain building on all the high voltages apparatuses. None the less the [...]

[...] The first 3 chapters of the DRSSTC design guide are now online. It is a long journey to read, find documentation and write this guide. It [...]

[...] I am currently working on a DRSSTC design guide where I try to put together best practises, lessons learned and explanations to the [...]

[...] I have completed building and initial testing of a new tube amplifier prototype using the Russian 6P45S tubes in the output stage. This prototype will be used for [...]

[...] received new enclosures for building a set of two mono tube amplifiers out from my 6P45S tube amplifier prototype and already have the power supply and mono stage circuit boards etched and half way [...]

[...] that they eventually failed, I have now upgraded the half bridge with a couple of IXGN60N60C2D1 isotop IGBT bricks. It is tuned much better now and is giving a fair amount of spark length, but I will [...]

[...] that they eventually failed, I have now upgraded the half bridge with a couple of IXGN60N60C2D1 isotop IGBT bricks. It is tuned much better now and is giving a fair amount of … Continue [...]